Phico D0 94v0 Lcd Display Datasheet Pdf

Most Phico D-0 character modules use a standard 16-pin layout: VSScap V sub cap S cap S end-sub Ground (0V) VDDcap V sub cap D cap D end-sub Power Supply (+5V) VEEcap V sub cap E cap E end-sub Contrast Adjustment Register Select (Data/Instruction) Read/Write Enable Signal Data Bus Lines (8-bit) Backlight Anode (+) Backlight Cathode (-)

While multiple versions exist, most Phico D-0 modules follow these general industrial standards: Power Supply : Typically requires for logic. : Standard parallel interface, often compatible with the HD44780 controller Connector Type : Varies between (standard character) and (graphics or dual-controller) configurations. Dimensions : A common 20x2 character version measures approximately 116mm x 37mm Standard 16-Pin Pinout

Microcontroller PHICO LCD Module +-------------------+ +-------------------+ | GND |---------->| Pin 1 (Vss) | | +5V |---------->| Pin 2 (Vdd) | | | [POT] | | | Digital Pin |---->|---->| Pin 3 (Vo) | | Digital Pin |---------->| Pin 4 (RS) | | GND |---------->| Pin 5 (R/W) | | Digital Pin |---------->| Pin 6 (E) | | Digital Pin |---------->| Pin 11 (DB4) | | Digital Pin |---------->| Pin 12 (DB5) | | Digital Pin |---------->| Pin 13 (DB6) | | Digital Pin |---------->| Pin 14 (DB7) | | +5V |--[Resist]-| Pin 15 (LED+) | | GND |---------->| Pin 16 (LED-) | +-------------------+ +-------------------+ Use code with caution. Note: Always place a current-limiting resistor (typically

: Forums like EDABoard provide community-verified pinouts for older modules.

After some digging, I found that the PHICO D0 94V0 is a 4.3-inch TFT LCD display module with a resolution of 480x272 pixels. Here are some interesting features and specs:

While exact dimensional specs can fluctuate depending on the sub-model suffix (such as the character-based DV-16100 module or the graphic WG320240C series ), the typical core engineering characteristics summarized in the Phico Datasheet PDF include: Standard Range / Specification -0.3V to +7.0V DC max (Typically operates at 5.0V ) Supply Current ( IDDcap I sub cap D cap D end-sub ) 2.0 mA to 5.0 mA Operating Temperature 0°C to +50°C Storage Temperature -20°C to +70°C Interface Options

Backlight anode power (+4.2V to +5V through current resistor) LED- / BLK Backlight cathode connection (Ground link)

If your Phico display features a standard single-row or double-row connector with 14 or 16 pins, it uses this parallel architecture. This makes it incredibly easy to drive using modern microcontrollers like Arduino, ESP32, or Raspberry Pi via standard LiquidCrystal libraries. Technical Specifications (Typical Values)

This public link is valid for 7 days and shares a thread, including any personal information you added. This link or copies made by others cannot be deleted. If you share with third parties, their policies apply. Can’t copy the link right now. Try again later.

Because "Phico D-0" is used across various displays, identify your specific unit by the secondary sticker or printed code: Go to product viewer dialog for this item. : 16 characters : 16 characters 2 lines (common in industrial equipment like fax machines).

Dimensions vary by the character configuration (e.g., 16x2, 20x2, or 40x2):

To find deeper reference material regarding timing diagrams, instruction sets, and DDRAM mapping, you can bypass the "PHICO" nomenclature and search directly for the standard or Sitronix ST7066 datasheet PDFs, as their functional guidelines apply identically to your module. If you'd like to narrow this down further, let me know:

Connecting Pin 15 directly to 5V without a current-limiting resistor can permanently destroy the backlight module or cause severe voltage drops on your microcontroller board.